Category Archives: laying

Technology of laying gypsum tiles with your hands

Gypsum tiles have to be laid properly, as not only the aesthetic appearance of decorative facing, but also the service life of

this substance will be dependent on the technology of work. The product is more universal, and it can be attached to plaster,

concrete, brick or gypsum board sheets, and provided that the top layer of the base is even and has no defects.

In the event the flaws of this foundation are significant, it ought to be completely treated with primer, then a cement mortar is

made, which matches all of the cracks. Subsequently the surface ought to be primed and dried. Primer treatment is essential to

improve the bond between the tile and the walls. In cases like this, its composition should decide on a particular, containing

components which block the look of fungus and mould.

In today’s interior of the rooms most frequently used gypsum tiles, even imitating natural brick or stone. To carry out cosmetic

finishing your self, it is essential first of all to choose a strategy of tile placement and prepare a solution. It’s necessary to

pay attention to the opposite side of the material. If its surface includes an embossed surface, then the adhesive should be put

using an even trowel, also if it’s even, then using a top notch one.

The tech of the job is as follows:

* A thin layer of glue is applied to the pre-prepared wall. It is distributed over the bottom so it is possible to put 4-5

tiles. Decorative cladding may be put both on plasterboard, also on putty.

* Cover the rear side of the tiles with adhesive.

* Plaster components are pushed against the walls and their location is corrected. To align the seams, it is advised to use

spacers.

* Finishing is performed in rows, each of which should be changed by half of a tile. Facing is completed to the corners of the

room, and then immediately get rid of any residual mortar at the joints.

Drying the walls takes no longer than a day also requires a continuous humidity and temperature inside the room. The last masterfasada.ru point in

the laying of gypsum tiles is the decoration. To try it, the joints between these elements are filled with a particular solution,

the shade of which suits the brick.

Decorative imitation of brickwork on the walls has been carried out in the following manners:

* Cutting the surface of the pits of masonry with a bolt cutter along with your own hands;

* placing of tiles under the brick:

* imitating the format and colour of the side surface of one brick;

* Imitating a fragment of brickwork of several bricks.

The very best way to decorate”under the brick” will be the one that permits you to create a usable coating with the maximum

appearance of its resemblance to organic masonry. All three strategies to execute this sort of finishing functions meet the needs,

however, the cutting of joints with a bolt is more labor-intensive and the formation of considerable amounts of dust, and so let

us consider more prevalent ways.

The old finish is removed from the walls, and also the surface, if needed, is leveled to get rid of the need to paste plaster on a

thick layer of glue.

Combining these cladding with other kinds of interior finishes may be both orderly and done with no apparent consistency,

chaotically, together with imitation of signs of aging.

With the help of cosmetic gypsum tiles it is possible to imitate a large number of textures.

A large number of textures can be imitated with the support of cosmetic gypsum tiles.

The wall on which it is to be installed must possess the following characteristics:

* Hardness and strength of the surface;

* The absence of irregular places and sharp differences;

* no deformations.

Decorative tiles in the interior of this kitchen

Walls are made from a variety of substances, so let’s break down the principles of setup.

When dealing with concrete, there’ll be no big problems. It is simply required to take into consideration the porosity of this

material. Concrete, which has nearly no pronounced pores, ought to be treated with a great primer.

Mounting gypsum tiles on concrete

Before starting work on the installation of gypsum tiles on the walls, then it’s worth assessing the strength of their surface.

When the plaster doesn’t fall off the wall and in exactly the exact same time holds nicely, it is possible to simply paint it

using primer.

Mount the tiles onto the painted concrete shouldn’t. The surface ought to be scratched, ensuring to misfire, and it should be

grouted and coated with a layer of plaster.